GoodWe Inverter Error Codes Pakistan 2026 — Complete Troubleshooting Guide

⚠️ GoodWe Inverter Error Codes — Complete Troubleshooting Guide Pakistan 2026

Every GoodWe error code explained with cause, severity and step-by-step fix. Covers ES, EM and DNS series. Save this page — it is the fastest way to diagnose your GoodWe problem.

📅 Updated November 2026  |  🇵🇰 Pakistan  |  ⚡ ES • EM • DNS

🔴 Critical Faults 🟠 Warnings 🟢 Info Codes 🔧 DIY Fixes

1. How to Read GoodWe Error Codes

GoodWe inverters show error codes on the LCD screen and in the SEMS Portal, PV Master and SolarGo apps. GoodWe's official codes are two-digit numbers (01–32), displayed with an "E" prefix in the apps — so "VAC Failure E15" means code 15, and "Utility Loss E23" means code 23. Battery alarms are separate bitmask numbers (4/8/16/32/64/128/256/512) shown as named alarms in PV Master, not as E-codes.

  • Critical faults: Safety or hardware faults — the inverter has stopped or must not be restarted without inspection. Red LED. Do not keep resetting these.
  • Warning codes: Grid or environmental conditions outside normal range — most self-clear when the grid or temperature returns to normal. Amber LED.
  • Battery alarms: Only occur on lithium batteries with BMS communication. Usually a cable, settings or state-of-charge issue, not a hardware failure.

Warning about fake code lists: a table circulating on Facebook claims "E01 = overcurrent of MOSFETs board" and similar definitions for E01–E08. That table comes from a generic off-grid manual, not GoodWe — E05, E06 and E08 are unassigned ("NA") in GoodWe's own manuals. Use only the codes on this page, verified against GoodWe's ES, EM, MT, SMT and DS series manuals.

2. E-Series Critical Fault Codes

CodeNameSeverityCommon Cause in PakistanFix
E14 Isolation Failure Critical PV-to-earth insulation resistance too low — monsoon moisture in MC4 connectors/DC isolators, damaged cable insulation, rodent damage on rooftops Do NOT restart repeatedly. Call installer for an insulation-resistance test of the DC array; often clears in dry weather if moisture is the cause.
E22 Ground I Failure Critical Ground leakage current too high — water ingress, damaged panel junction box, degraded DC cabling after monsoon Safety fault — switch off and call the installer; do not ignore.
E26 / E32 GFCI Failure Critical The leakage-current detection circuit itself has failed, so the inverter can no longer monitor earth leakage Stop using the system; installer/service centre only — the safety monitoring circuit needs repair.
E17 PV Over Voltage Critical String open-circuit voltage above the inverter's max DC input — too many panels in series, or cold winter mornings in northern Pakistan raising Voc Do NOT restart without inspection. Installer must reconfigure the string (fewer panels per string) and check panel bypass diodes.
E21 DC Bus High Critical Internal DC bus voltage too high — often linked to excessive PV input voltage Switch DC isolator off/on once (30 s gap); if it persists, installer service required.
E01 SPI Failure Critical Internal communication failure between microcontrollers (can be triggered by strong external magnetic fields) Restart once; if it returns, control-board service/replacement — installer only.
E02 EEPROM R/W Failure Critical Memory chip read/write failure Restart once; if persistent, firmware re-flash or control-board replacement.
E07 / E25 Relay Check Failure Critical Relay self-check failed — the inverter cannot confirm its isolation relay works Restart once only; if it survives a restart, do NOT keep resetting — relay board replacement needed.
E13 DC Injection High Critical DC component of AC output current exceeds the limit — measurement-circuit or internal component fault Full restart (AC off → DC off → 5 min → DC on → AC on); if persistent, installer service.

3. E-Series Warning Codes

CodeNameSeverityCommon Cause in PakistanFix
E03 Fac Failure Warning Grid frequency drifts outside ~49.5–50.5 Hz — common during load-shedding recovery, generator changeover, or weak DISCO feeders Usually self-clears within 5 min. If frequent, check the inverter's safety-country setting is correct; persistent cases need the DISCO/installer to check grid stability.
E04 Fac Failure (slave) Warning Slave processor detects grid frequency out of range — same Pakistan grid-instability causes as E03 Same as E03; if persistent, installer/firmware check.
E15 Vac Failure Warning Grid voltage out of range — Pakistan's chronic problem: high voltage at midday in high-solar streets, low voltage (under ~200 V) on overloaded feeders in summer Self-clears when voltage normalises. If daily, have the installer check AC cable sizing/length and volt-watt settings, and ask the DISCO for a tap/voltage check.
E23 Utility Loss Warning No grid detected — load-shedding, tripped AC breaker, or loose AC wiring Check AC breaker/isolator is on and grid is actually available; check AC cable connections; if grid is live but code persists, call the installer.
E00 GFCI Check Timeout Warning Leakage self-test took too long, usually moisture on the array after rain Restart once; if it recurs, contact the service centre.
E19 Over Temperature Warning Inverter case overheating — very common in Pakistan: 45 °C+ summers, inverters mounted in direct sun or unventilated rooms Improve ventilation/shade, clear debris from heatsink fins, keep 300 mm clearance; unit derates then shuts down to protect itself.
E16 EFan Fault Warning External cooling fan failed — dust build-up is the usual cause in Pakistan's dusty environment Clean/obstruction-check the fan; restart once; if persistent, the fan motor needs replacement.
E20 IFan Fault Warning Internal fan failure — dust/heat Restart once; if persistent, fan replacement by installer.
E12 LCD Communication Failure Warning Communication error between LCD DSP and master DSP (MT/DNS LCD models) Restart; if persistent, ribbon cable/LCD board check by installer.

4. Battery & Hybrid Alarms

These alarms appear in the PV Master app as named battery alarms (with bitmask numbers). They only occur when a lithium battery with BMS communication is connected.

CodeNameSeverityCommon Cause in PakistanFix
256 Battery Communication Failure Warning BMS comms lost — loose CAN/RS485 cable between inverter and lithium battery, wrong battery model selected in app, or battery in standby (very common with third-party batteries in Pakistan) Check BMS cable is secure and in the correct port; verify correct battery model is selected in SolarGo/PV Master; restart the battery per its manual.
128 Battery Under Total Voltage Warning Battery deeply discharged — long load-shedding with no solar, or battery left disconnected Let solar recharge it; some batteries need a manual wake-up (e.g. GoodWe SECU-A: press battery switch 5 times in 10 s to force MOS closed).
8 Battery Over Total Voltage Critical Battery voltage above inverter's max — wrong battery type/configuration Check battery-type setting; installer must verify battery/inverter compatibility.
64 Battery Under SOC Warning State of charge critically low — protective stop Normal protective behaviour; recharges from solar when available.
— Back-Up Over Load Warning Load on backup output exceeds rated backup capacity — running AC/geyser on backup during load-shedding Reduce backup-circuit loads (heaters, large ACs, kettles); backup output rating is lower than grid-tied rating.

5. Most Common GoodWe Problems in Pakistan

🔴 Problem: E15 (Vac Failure) every day at midday

Pakistan's most common GoodWe complaint. When many rooftop systems on the same street export at midday, local grid voltage rises above the inverter's limit and it disconnects. Fix: usually self-clears within minutes. If it happens daily, have your installer check the AC cable size and length (thin or long cables raise voltage at the inverter) and ask your DISCO for a voltage/tap check. Do not widen protection limits without approval.

🔴 Problem: E23 (Utility Loss) during load-shedding

Normal behaviour for on-grid GoodWe models — the inverter must disconnect when the grid drops. If E23 appears while the grid is live, check the AC breaker and isolator are on, and check the AC cable connections. Persistent E23 with a live grid needs an installer visit.

🔴 Problem: E19 (Over Temperature) in June–August

Pakistan's most common summer issue. An inverter mounted on a south-facing wall in direct afternoon sun can reach 70–80°C — well above its rated limit. Fix: relocate to a shaded north-facing wall or indoors, add a shade canopy if relocation is impossible, and clean the heatsink fins. This single fix often eliminates most summer inverter problems.

🔴 Problem: Battery alarm 256 (Communication Failure)

The most common hybrid problem in Pakistan — almost always a wiring or settings issue, not hardware failure. Check the CAN/RS485 cable is secure and in the correct port, verify the correct battery model is selected in SolarGo or PV Master, then restart the battery per its manual. Third-party batteries are the usual trigger.

6. First-Response Checklist — Any GoodWe Error

  • Note the exact error code displayed on screen or in SEMS/PV Master — write it down before doing anything else
  • Check if the error appeared during load-shedding restoration, extreme heat, heavy rain, or a dust storm — these are the most common Pakistan triggers
  • For warning codes (E03, E04, E15, E23): wait 5 minutes — most self-clear when the grid stabilises
  • Power cycle the inverter: DC isolator off → AC circuit breaker off → wait 3 minutes → AC on → DC on. Most warning codes and some fault codes self-clear after a power cycle
  • For E14, E22 or E26 (isolation/ground faults) — stop here, do NOT power on again. Call your installer immediately
  • For battery alarms — check the BMS cable and the battery model setting in the app before anything else
  • If the inverter is within warranty, contact your authorized GoodWe dealer with the error code, inverter serial number, and a SEMS screenshot

Frequently Asked Questions

Pehle: screen ya SEMS app pe error code dekho. Phir: DC isolator band karo, AC breaker band karo, 3 minute ruko, phir AC on karo, phir DC on. Agar code E19 hai (overheat): inverter ko dhoop se bahar rakhna zaroori hai. Agar E14 ya E22 hai: bilkul mat chalao — installer bulao. Agar E15 ya E23 hai: aksar grid voltage ka masla hai, aksar khud theek ho jata hai.

E15 means grid voltage went out of range. In Pakistan this is usually high voltage at midday (many rooftop systems exporting on the same street) or low voltage on overloaded feeders in summer evenings. It self-clears when voltage normalises. If it happens daily, have your installer check AC cable sizing and ask your DISCO for a voltage check.

E23 means the inverter cannot detect the grid. During load-shedding this is normal — the inverter must disconnect. If the grid is live and E23 persists, check your AC breaker and isolator are on and the AC cable connections are firm. Persistent E23 with a live grid needs an installer.

E19 means the inverter case is overheating. In Pakistan this is almost always an installation-location problem: direct sun, an unventilated room, or blocked heatsink fins. Shade the inverter, clean the fins, keep 300 mm clearance around it, and relocate it to a shaded wall if the problem recurs every summer.

Alarm 256 is a battery communication failure — the inverter lost BMS contact with the lithium battery. Check the CAN/RS485 cable is secure and in the correct port, verify the correct battery model is selected in SolarGo or PV Master, and restart the battery per its manual. It is very common with third-party batteries in Pakistan.

Need Help with Your GoodWe?

If error codes persist after following this guide, get help from a verified GoodWe installer in your city.

🔧 Find GoodWe Installer 📖 GoodWe Review

Leave a Reply

Your email address will not be published. Required fields are marked *